Generate QR code
Open Access
Subscription Access
Comparisons of national standards of the unit of length in the field of measurement of parameters of form deviation the fiatness of optical surfaces COOMET.L-S15
https://doi.org/10.32446/0368-1025it.2021-7-60-64
Abstract
Precision interference measurement of parameters of form optical surfaces are one of the most important type of the measurement in the field of the geometrical values. In countries-participants of this comparisons the special primary standards in this field of measurements take part in reproduction and transmission the unit of length in this field of measurements ensuring high measuring and calibrating capabilities countries in this type of measurement. In this article presents the result of supplementary comparisons COOMET 570/UA-a/12. The result of comparisons allowed to declare to Belarus and Russia, and to confirm to Ukraine their measuring and calibrating capability in database CIPM MRA.
About the Authors
O. L. Kostrikov
National Science Center “Institute of Metrology”
Ukraine
Ukraine
Oleksandr L. Kostrikov
Kharkov
V. S. Kupko
National Science Center “Institute of Metrology”
Ukraine
Ukraine
Volodymyr S. Kupko
Kharkov
A. I. Shloma
National Science Center “Institute of Metrology”
Ukraine
Ukraine
Andrii I. Shloma
Kharkov
D. A. Novikov
Russian Research Institute for Metrological Service
Russian Federation
Russian Federation
Denis A. Novikov
Moscow
V. G. Lysenko
Russian Research Institute for Metrological Service
Russian Federation
Russian Federation
Valery G. Lysenko
Moscow
K. A. Milovanova
Russian Research Institute for Metrological Service
Russian Federation
Russian Federation
Kate A. Milovanova
Moscow
N. A. abachnikova
Russian Research Institute for Metrological Service
Russian Federation
Russian Federation
Natalia A. Tabachnikova
Moscow
V. B. Makarevich
Belarussian State Institute of Metrology
Belarus
Belarus
Vladimir B. Makarevich
Minsk
References
1. Comparison of flatness and surface roughness parameters when face milling and turning, ed. W. Zebala, I. Mankova, Cracow university technology development in machining technology, 2017, vol. 7, pp. 18–27.
2. Novikov D. A., Kononogov S. A., Zolotarevskii S. Yu., Vishnyakov G. N., Gusev A. S., Levin G. G., Lyaskovskii V. L., Measurement Techniques, 2013, vol. 56, no. 9, pp. 1006–1010. https://doi.org/10.1007/s11018-013-0320-0
3. Zolotarevsky S. Yu., Novikov D. A.,Gusev A. S., Lyaskovskii V. L., Measurement Techniques, 2013, vol. 56, no. 3, pp. 247– 251. https://doi.org/10.1007/s11018-013-0188-z
4. Krutikov V. N., Zolotarevsky S. Yu., Lysenko V. G., Topological parameters of functional surface texture, Metrologiya, 2013, no. 2, pp. 25–32. (In Russ.)
5. Final report of the comparisons (COOMET.L-S15), Metrologia, 2018, vol. 55, Tech. suppl. 04006.
6. Vishnyakov G. N, Novikov D. A., Measuring-calibrating installation on the base of wide-fi eld Fizo interometry, Metrologiya, 2012, no. 12, pp. 17–24. (In Russ.)
7. Gorshkov V. A., Lomakin A. G., Nevrov A. S., Novikov D. A., A technological program for processing interferograms by Fourier transformation, Optical Journal, 2011, vol. 78, no. 4, pp. 44– 50. (In Russ.)
8. Lysenko V. G., Tabachnikova N. A., Novikov D. A., State primary special standard the unit of length for parameters of fl athness of optical surfaces size till 200 mm, Zakonodatel’naya i prikladnaya metrologiya, 2015, no.6, рр. 10–13. (In Russ.)
9. Chunovkina A. G., Kharitonov I. A., Measurement Techniques, 2007, vol. 50, no. 7, pp. 711–714. https://doi.org/10.1007/s11018-007-0136-x
10. Chunovkina A. G., Burmistrova N. A., Zvyagin N. D., Measurement Techniques, 2013, vol. 56, no. 6, pp. 577–583. https://doi.org/10.1007/s11018-013-0248-4
11. Burmistrova N. A., Measurement Techniques, 2015, vol. 57, no. 10, pp. 1103–1112. https://doi.org/10.1007/s11018-015-0587-4
Review
For citations:
Kostrikov O.L., Kupko V.S., Shloma A.I., Novikov D.A., Lysenko V.G., Milovanova K.A., abachnikova N.A., Makarevich V.B. Comparisons of national standards of the unit of length in the field of measurement of parameters of form deviation the fiatness of optical surfaces COOMET.L-S15. Izmeritel`naya Tekhnika. 2021;(7):60-64. (In Russ.) https://doi.org/10.32446/0368-1025it.2021-7-60-64
Views:
92
Email this article 